Lunatico Astronomia S. L Port Devices Driver Download

Posted on

As an engineer I feel I can do this easily and at a much lower cost than Lunatico Astronomia’s own optional anemometer with built-in heater. The ambient light sensor will respond to moonlight or domestic light spill so threshold settings need carefull adjustment to avoid false readings and unnecessary observatory unsafe conditions shutdown. As the Solo has its own serial port, and publishes information in the local network, you'll get rid of any USB/Serial devices and drivers issues. To install it: disconnect the AAG's RS232 from your PC, and connect it to the Solo; remove power from the AAG CW, and use the same cable to power on the Solo.

Welcome to the ASCOM Initiative

Port
The following live stream videos are nearly an hour long each. We gave thought to chopping them down, but in the end if you are seriously interested in learning what we're doing to drive astronomy software forward, we hope you'll devote the time to learning. If you're new to all of this, we suggest you watch the Non-Technical Overview first.

This is the home of the ASCOM Initiative, a loosely-knit group of astronomy software developers and astronomy device manufacturers devoted to vendor-independent plug-and-play control. ASCOM is a many-to-many and language-independent architecture, supported by most astronomy devices which connect to Windows and now Linux and MacOS computers. The diagram below shows how ASCOM differs from traditional astronomy instrument control architectures. This architecture applies to both Windows/COM and cross-platform Alpaca technologies.

ASCOM Platform 6.5SP1 is Current

For more information on the ASCOM Initiative, see the About ASCOM section.

In my case I was most intrigued by this website:. Installs a driver for the Astro-Physics series of telescope mounts. This driver provides combined telescope, focuser, and dome interfaces each of which may be used by separate programs. Here is a list of the hardware I used: Here are the passing results. I ran the four wires from these two motor ports to the pins of a female DB9 connector. Feather Touch Focuser 4.

Uploader:Tacage
Date Added:9 March 2018
File Size:55.56 Mb
Operating Systems:Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads:58119
Price:Free* [*Free Regsitration Required]

The rotary encoder support was so I could manually focus the telescope. Lunatico’s Seletek Focuser Software and drivers for the Seletek family of controllers. I added support for the TMP36 so Aascom could have a temperature reading from the focuser. Micro Focuser all models Drivers for all models of the Micro Focuser line of precision focusers.

This driver provides combined telescope, focuser, and dome interfaces each of which may be used by separate programs. I wired one arm of the stepper across the M3 motor port and the other arm across the M4 motor port.

This makes it compatible with the cable that came with my Robofocus controller and I can plug my Robofocus stepper motor straight into the box with no problems. I’m still experimenting with this as that seems to give almost too fine of control.

Arduino-based Motor Focuser Controller.

MSFASTRO.NET

RoboFocus Control Program 5. Most programs such as MaxIm DL already have the needed focus controls built in. Installs a driver for the Astro-Physics series of telescope mounts. Link to download the driver can be found at the bottom of the page you see when you click the Visit button.

Note about wiring the stepper motor – the stepper I am using is a bipolar stepper. Unless you focussr this full-function program or the multiple drivers, use the basic driver listed above. In my case I was most intrigued by this website:. I ran the four wires from these two motor ports to the pins of a female DB9 connector.

I started with the code from the above website and made the following changes: The one downside is that the Robofocus controller is a bit on the expensive side. Use this for most applications. I set it up so one step on the rotary encoder moved the stepper on the focuser by one step.

This can be used to track when you might need to refocus as the temperature changes. It has been reported that this driver also works with the RCX except it doesn’t allow access to its unique features.

Lunatico astronomia s. l port devices driver download windows 7

Lunatico Astronomia S. L Port Devices Driver Download Windows 10

Feather Touch Focuser 4. This meant you just had to program your Arduino board with his code and the official Moonlite ASCOM driver would attach to your Arduino and “just work”. Mind computer products laptops & desktops driver.

Here are the passing results. This driver provides both telescope and focuser interfaces each of which may be used by separate programs.

Focuser Drivers

Here is a list of the hardware I used: Fortunately there have been many individuals who have explored using an Arduino with one of the many low cost stepper controller boards to build a focus controller.

I need to try it when I am imaging planets or the Moon as that is where I thought manual control would be most beneficial. This driver has the ability to create several drivers giving the ability to control multiple focusers on the same system. Removed the dependency on the AccelStepper library – I didn’t feel I needed this capability for my geared Robofocus stepper motor.

Lunatico Astronomia S. L Port Devices Driver Download Windows 7

I have been using a Robofocus focus controller for many years now to control a Robofocus geared stepper motor on my various imaging telescopes.

Recent Drivers